NEW ACCEPTED IEC STANDARDS IN THE IECEE CB-SCHEME

GUIDELINES

The Member NCB(s) of the IECEE are the sole Organizations in conjunction with their associated CBTL(s), in the field of the IECEE operations, entitled to apply to operate the relevant IEC standard(s), edition(s) and amendment(s).

When National Differences exist against the relevant IEC standards, it is the responsibility of the Member NCB(s) to declare such status for each standard/edition(s)/amendment(s) and provide details of such National Differences by sending an email with the details to the IECEE Secretariat.

The Member Body is required to endorse the National Differences, Special National Conditions, Group Differences, by being copied in the email sent to the IECEE Secretariat. Regulatory Requirements shall be declared under the responsibility of the NCB.

IECEE Member NCB(s) are kindly requested to provide this information in electronic format (MSWord).

The Member NCB(s) “Scope Extension Request” can be declared/requested either by using the:

*Note: The Fast Track Extension request requires an application that shall be addressed to the IECEE Secretariat according to draft OD-CB2007 as applicable.

**Note: The Scope Extension request requires an application that shall be addressed to the IECEE Secretariat according to OD-CB2007 Part 5 or 7 as applicable.

For Member NCB(s) located in the same country where Regulatory Requirements, National Differences, Special National Conditions and Group Differences apply, it is the responsibility of the Member NCB(s) to coordinate, nationally, in order to provide the required information to the IECEE Secretariat once.

Of course the NCB must coordinate with their Member Body or the IEC National Committee to make sure that they are provided with the appropriate information.


Previously accepted IEC Standards in the IECEE CB-Scheme - Just Published No, 1 (2007-01-12)
Previously accepted IEC Standards in the IECEE CB-Scheme - Just Published No, 2 (2007-04-23)

BATT - Batteries

IEC 60086-1(ed.10) (2007-03)
Primary batteries - Part 1: General

IEC 60086-4(ed.3) (2007-09)
Primary batteries - Part 4: Safety of lithium batteries

IEC/TS 62257-8-1(ed.1) (2007-06)
Recommendations for small renewable energy and hybrid systems for rural electrification - Part 8-1: Selection of batteries and battery management systems for stand-alone electrification systems - Specific case of automotive flooded lead-acid batteries available in developing countries

CABL - Cables and Cords IEC 60227-1(ed.3) (2007-10) Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V - Part 1: General requirements IEC 60245-1(ed.1);am1 (2007-10) Amendment 1 - Rubber insulated cables - Rated voltages up to and including 450/750 V - Part 1: General requirements Back to the top

CAP - Capacitors as components

IEC 60384-20(ed.2) (2008-01)
Fixed capacitors for use in electronic equipment - Part 20: Sectional specification - Fixed metallized polyphenylene sulfide film dielectric surface mount d.c. capacitors

CONT - Switches for appliances and automatic controls for electrical household appliances

IEC 60730-2-14(ed.1);am2 (2007-11)
Amendment 2 - Automatic electrical controls for household and similar use - Part 2-14: Particular requirements for electric actuators

IEC 60730-2-15(ed.2) (2008-01)
Automatic electrical controls for household and similar use - Part 2-15: Particular requirements for automatic electrical air flow, water flow and water level sensing controls

IEC 60730-2-17(ed.1);am2 (2007-08)
Amendment 2 - Automatic electrical controls for household and similar use - Part 2-17: Particular requirements for electrically operated gas valves, including mechanical requirements

IEC 60730-2-19(ed.1);am2 (2007-08)
Amendment 2 - Automatic electrical controls for household and similar use - Part 2-19: Particular requirements for electrically operated oil valves, including mechanical requirements

EMC - Electromagnetic Compatability

CISPR 12(ed.6) (2007-05)
Vehicles, boats and internal combustion engines - Radio disturbance characteristics - Limits and methods of measurement for the protection of off-board receivers

CISPR 16-1-1(ed.2);am2 (2007-07)
Amendment 2 - Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-1: Radio disturbance and immunity measuring apparatus - Measuring apparatus

CISPR 16-1-4(ed.2);am1 (2007-10)
Amendment 1 - Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-4: Radio disturbance and immunity measuring apparatus - Ancillary equipment - Radiated disturbances

CISPR/TR 16-4-1(ed.2);am2 (2007-04)
Amendment 2 - Specification for radio disturbance and immunity measuring apparatus and methods - Part 4-1: Uncertainties, statistics and limit modelling - Uncertainties in standardized EMC tests

IEC 60034-8(ed.3) (2007-06)
Rotating electrical machines - Part 8: Terminal markings and direction of rotation

IEC 60255-22-3(Ed.3) (2007-07)
Measuring relays and protection equipment - Part 22-3: Electrical disturbance tests - Radiated electromagnetic field immunity

IEC 61326-3-1(ed.1) (2008-01)
Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 3-1: Immunity requirements for safety-related systems and for equipment intended to perform safety-related functions (functional safety) - General industrial applications

IEC 61326-3-2(ed.1) (2008-01)
Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 3-2: Immunity requirements for safety-related systems and for equipment intended to perform safety-related functions (functional safety) - Industrial applications with specified electromagnetic environment

HOUS - Household and similar equipment

IEC 60312(ed.4) (2007-04)
Vacuum cleaners for household use - Methods of measuring the performance

IEC 60335-2-6(ed.5);am2 (2008-01)
Amendment 2 - Household and similar electrical appliances - Safety - Part 2-6: Particular requirements for stationary cooking ranges, hobs, ovens and similar appliances

IEC 60335-2-13(ed.5);am2 (2008-01)
Amendment 2 - Household and similar electrical appliances - Safety - Part 2-13: Particular requirements for deep fat fryers, frying pans and similar appliances

IEC 60335-2-23(ed.5);am1 (2008-01)
Amendment 1 - Household and similar electrical appliances - Safety - Part 2-23: Particular requirements for appliances for skin or hair care

IEC 60335-2-30(ed.4)am2 (2007-03)
Amendment 2 - Household and similar electrical appliances - Safety - Part 2-30: Particular requirements for room heaters

IEC 60335-2-32(ed.4);am1 (2008-01)
Amendment 1 - Household and similar electrical appliances - Safety - Part 2-32: Particular requirements for massage appliances

IEC 60601-2-33(ed.2);am2 (2007-11)
Amendment 2 - Medical electrical equipment - Part 2-33: Particular requirements for the safety of magnetic resonance equipment for medical diagnosis

IEC 60335-2-36(ed.5);am2 (2008-02)
Amendment 2 - Household and similar electrical appliances - Safety - Part 2-36: Particular requirements for commercial electric cooking ranges, ovens, hobs and hob elements

IEC 60335-2-37(ed.5)am1 (2008-02)
Amendment 1 - Household and similar electrical appliances - Safety - Part 2-37: Particular requirements for commercial electric deep fat fryers

IEC 60335-2-38(ed.5)am1 (2008-02)
Amendment 1 - Household and similar electrical appliances - Safety - Part 2-38: Particular requirements for commercial electric griddles and griddle grills

IEC 60335-2-48(ed.4)am1 (2008-02)
Amendment 1 - Household and similar electrical appliances - Safety - Part 2-48: Particular requirements for commercial electric grillers and toasters

IEC 60335-2-50(ed.4);am1 (2007-12)
Amendment 1 - Household and similar electrical appliances - Safety - Part 2-50: Particular requirements for commercial electric bains-marie

IEC 60335-2-58(ed.3)am1 (2008-02)
Amendment 1 - Household and similar electrical appliances - Safety - Part 2-58: Particular requirements for commercial electric dishwashing machines

IEC 60335-2-62(ed.3)-am1 (2008-02)
Amendment 1 - Household and similar electrical appliances - Safety - Part 2-62: Particular requirements for commercial electric rinsing sinks

IEC 60335-2-64(ed.3);am1 (2007-12)
Amendment 1 - Household and similar electrical appliances - Safety - Part 2-64: Particular requirements for commercial electric kitchen machines

IEC 60335-2-69(ed.3);am2 (2007-12)
Amendment 2 - Household and similar electrical appliances - Safety - Part 2-69: Particular requirements for wet and dry vacuum cleaners, including power brush, for industrial and commercial use

IEC 60335-2-79(ed.2)am2 (2007-07)
Amendment 2 - Household and similar electrical appliances - Safety - Part 2-79: Particular requirements for high pressure cleaners and steam cleaners

IEC 60335-2-87(ed.2);am1 (2007-03)
Amendment 1 - Household and similar electrical appliances - Safety - Part 2-87: Particular requirements for electrical animal-stunning equipment

IEC 60335-2-91(ed.3) (2008-02)
Household and similar electrical appliances - Safety - Part 2-91: Particular requirements for walk-behind and hand-held lawn trimmers and lawn edge trimmers

IEC 60335-2-94(ed.3) (2008-01)
Household and similar electrical appliances - Safety - Part 2-94: Particular requirements for scissors type grass shears

IEC 60335-2-108 (2008-01)
Household and similar electrical appliances - Safety - Part 2-108: Particular requirements for electrolysers

INST - Installation accessories and connection devices

IEC 60320-1(ed.2);am1 (2007-08)
Amendment 1 - Appliances couplers for household and similar general purposes - Part 1: General requirements

IEC 60364-7-708(ed.2) (2007-05)
Low-voltage electrical installations - Part 7-708: Requirements for special installations or locations - Caravan parks, camping parks and similar locations

IEC 60364-7-721(ed.1) (2007-04)
Low-voltage electrical installations - Part 7-721: Requirements for special installations or locations - Electrical installations in caravans and motor caravans

IEC 60423(ed.3) (2007-08)
Conduit systems for cable management - Outside diameters of conduits for electrical installations and threads for conduits and fittings

IEC 60884-2-4(ed.3) (2007-11)
Plugs and socket-outlets for household and similar purposes - Part 2-4: Particular requirements for plugs and socket-outlets for SELV

IEC 61058-1(ed.3);am2 (2007-11)
Amendment 2 - Switches for appliances - Part 1: General requirements

IEC 61242(ed.1);am1 (2008-01)
Amendment 1 - Electrical accessories - Cable reels for household and similar purposes

IEC 61537(ed.2) (2006-10)
Cable management - Cable tray systems and cable ladder systems

LITE - Lighting

IEC 60598-2-22(ed.3);am2 (2008-01)
Amendment 2 - Luminaires - Part 2-22: Particular requirements - Luminaires for emergency lighting

IEC 60901(ed.2)am1 (1997-06)
Amendment 1 - Single-capped fluorescent lamps - Performance specifications

IEC 60927(ed.3) (2007-06)
Auxiliaries for lamps - Starting devices (other than glow starters) - Performance requirements

IEC 62031(ed.1) (2008-01)
LED modules for general lighting - Safety specifications

IEC/TS 62257-12-1(ed.1) (2007-06)
Recommendations for small renewable energy and hybrid systems for rural electrification - Part 12-1: Selection of self-ballasted lamps (CFL) for rural electrification systems and recommendations for household lighting equipment

MEAS - Measurement, Control and Laboratory equipment

IEC 61557-6(ed.2) (2007-07)
Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. - Equipment for testing, measuring or monitoring of protective measures - Part 6: Effectiveness of residual current devices (RCD) in TT, TN and IT systems

IEC 61557-8(ed.2) (2007-01)
Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. - Equipment for testing, measuring or monitoring of protective measures - Part 8: Insulation monitoring devices for IT systems

IEC 61557-12(ed.1) (2007-08)
Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. - Equipment for testing, measuring or monitoring of protective measures - Part 12: Performance measuring and monitoring devices (PMD)

MED - Electrical equipment for medical use

IEC 60601-1-2(ed.3) (2007-03)
Medical electrical equipment - Part 1-2: General requirements for basic safety and essential performance - Collateral standard: Electromagnetic compatibility - Requirements and tests

IEC 60601-1-3(ed.2) (2008-01)
Medical electrical equipment - Part 1-3: General requirements for basic safety and essential performance - Collateral Standard: Radiation protection in diagnostic X-ray equipment

IEC 60601-1-10(ed.1) (2007-11)
Medical electrical equipment - Part 1-10: General requirements for basic safety and essential performance - Collateral Standard: Requirements for the development of physiologic closed-loop controllers

IEC 60601-2-22(ed.3) (2007-05)
Medical electrical equipment - Part 2-22: Particular requirements for basic safety and essential performance of surgical, cosmetic, therapeutic and diagnostic laser equipment

IEC 60601-2-37(ed.2) (2007-08)
Medical electrical equipment - Part 2-37: Particular requirements for the basic safety and essential performance of ultrasonic medical diagnostic and monitoring equipment

IEC 60601-2-39(ed.2) (2007-11)
Medical electrical equipment - Part 2-39: Particular requirements for basic safety and essential performance of peritoneal dialysis equipment

IEC 62353(ed.1) (2007-05)
Medical electrical equipment - Recurrent test and test after repair of medical electrical equipment

IEC/TS 62462(ed.1) (2007-05)
Ultrasonics - Output Test - Guide for the maintenance of ultrasound physiotherapy systems

MISC - Miscellaneous

IEC 60747-5-5(ed.1) (2007-09)
Semiconductor devices - Discrete devices - Part 5-5: Optoelectronic devices - Photocouplers

IEC 61318(ed.3) (2007-11)
Live working - Conformity assessment applicable to tools, devices and equipment

IEC 61340-5-1(Ed.1) (2007-08)
Electrostatics - Part 5-1: Protection of electronic devices from electrostatic phenomena - General requirements

IEC 62220-1-2(ed.1) (2007-06)
Medical electrical equipment - Characteristics of digital X-ray imaging devices - Part 1-2: Determination of the detective quantum efficiency - Detectors used in mammography

OFF - IT and office equipment

IEC 60825-1(ed.2) (2007-03)
Safety of laser products - Part 1: Equipment classification and requirements

POW - Low voltage, high power switching equipment

IEC 60947-1(Ed.5) (2007-06)
Low-voltage switchgear and controlgear - Part 1: General rules

IEC 60947-5-2(Ed.3) (2007-10)
Low-voltage switchgear and controlgear - Part 5-2: Control circuit devices and switching elements - Proximity switches

IEC 60974-10(ed.2) (2007-08)
Arc welding equipment - Part 10: Electromagnetic compatibility (EMC) requirements

IEC 62026-1(ed.2) (2007-06)
Low-voltage switchgear and controlgear - Controller-device interfaces (CDIs) - Part 1: General rules

IEC 62026-2(ed.2) (2008-01)
Low-voltage switchgear and controlgear - Controller-device interfaces (CDIs) - Part 2: Actuator sensor interface (AS-i)

IEC 62026-3(ed.2) (2008-01)
Low-voltage switchgear and controlgear - Controller-device interfaces (CDIs) - Part 3: DeviceNet

PROT - Installation protective equipment

IEC 60127-1(ed.2) (2006-06)
Miniature fuses - Part 1: Definitions for miniature fuses and general requirements for miniature fuse-links

PV - Photovoltaics

IEC/TS 62257-9-5(ed.1) (2007-06)
Recommendations for small renewable energy and hybrid systems for rural electrification - Part 9-5: Integrated system - Selection of portable PV lanterns for rural electrification projects

SAFE - Saftey transformers and similar equipment

No new IEC standard(s)

TOOL - Portable tools

IEC 60745-2-16 (2008-02)
Hand-held motor-operated electric tools - Safety - Part 2-16: Particular requirements for tackers

TOYS - Electric Toys

No new IEC standard(s)

TRON - Electronics, entertainment

No new IEC standard(s)

NOTE:

If you have a received a request from the industry to certify for any additional IEC standard(s) that is not listed here, that you would like to add to the IECEE CB-Scheme, please send the IECEE Secretariat an email.

WITHDRAWN/REPLACED PUBLICATIONS

Copyright © IECEE 2007. All Rights Reserved.

If you have any questions and/or comments, please contact The IECEE Secretariat.